Product

Steam Coil Air Preheater (SCAPH)

Finned steam coils that preheat combustion air — recovering boiler steam energy and protecting downstream air heaters in fouling-prone flue gas.

What is a steam coil air preheater?

A steam coil air preheater (SCAPH) is a finned-tube, steam-to-air heat exchanger. Saturated (or suitable process) steam flows inside the tubes; combustion air crosses the external fins and picks up heat. Units are typically installed in the FD-fan duct, ahead of the main tubular or regenerative air preheater.

Grandeh fabricates next-generation G-type finned tube SCAPH coils for industrial steam service — with attention to thermal duty, drainability and IBR-aligned pressure-part practice at Aurangabad works.

Why plants specify SCAPH

  • Raise combustion-air temperature during start-up and low-load when flue gas alone is not enough
  • Help keep main-APH cold-end surfaces warmer — reducing acid dew-point corrosion risk
  • Protect tubular / regenerative APHs when flue gas is sticky, acidic or ash-laden (spent-wash, biomass)
  • Stabilise air temperature for combustion and burner performance where plant procedures allow

How SCAPH works

  • Steam side — steam enters the inlet header, distributes through the tube bundle and condenses as it releases latent heat
  • Air side — the FD fan drives ambient or process air across the fins; warmed air continues to the main APH or furnace
  • Condensate — drains through the return header, traps and vents so coils stay free of water hammer and air locking
Grandeh steam coil air preheater (SCAPH) finned coil unit

Main components

A complete SCAPH package combines heat-transfer hardware with drainage, control and duct interfaces. Grandeh fabricates the coil, headers and casing; valves, instruments and actuators are integrated to project preference.

ComponentRole
Finned tube bundlePrimary steam-to-air heat transfer (G-type / spiral fins)
Steam inlet headerEven steam distribution into the coil tubes
Return headerCollects condensate from the tube rows
Condensate drains & ventsRemoves condensate and non-condensables; limits water hammer
Casing / duct housingSupports the coil and guides airflow with low leakage
Steam control valveModulates heating capacity to air-outlet temperature
Temperature / pressure instrumentsAir and steam monitoring for control and diagnostics
Air bypass damperBypasses the coil when preheating is not required — see also Grandeh dampers
Supports & expansion jointsCarry mechanical loads and thermal movement

What information is required to size SCAPH?

Accurate selection needs verified air-side, steam-side and site data — for design, start-up and low-load cases where relevant.

Air-side design data

  • Air mass or volumetric flow (kg/s, Nm³/h or m³/h)
  • Inlet-air temperature (°C) — including minimum ambient / design case
  • Required outlet-air temperature or temperature lift (°C)
  • Maximum allowable air-side pressure drop (Pa or mmWC)
  • Dust, moisture or contaminants in the air stream
  • Duct width, height, orientation and available length

Steam and condensate data

  • Available steam pressure (bar) and temperature (°C)
  • Saturated or superheated condition; available steam flow limits
  • Required heat duty (kW) if already calculated
  • Condensate return pressure and preferred trap / drain routing

Mechanical and site data

  • Preferred tube, fin, header and casing materials
  • Horizontal or vertical coil orientation; maintenance / pull-out clearance
  • Flange standards, connection sizes and support arrangement
  • IBR / TPI / documentation scope for the purchase order

Share process data and duct sketches with your enquiry — we will propose coil rows, face velocity and materials that fit fan and steam limits.

Technical focus

ParameterGrandeh SCAPH practice
Equipment typeSteam-to-air finned-tube heat exchanger
Coil typeG-type / spiral finned tubes
Heating mediumSaturated or suitable process steam
Heated mediumCombustion / ambient / process air
Typical serviceSpent-wash / slop, biomass, cold start-up, low load
Design careDrainable circuits, header sizing, air-side ΔP within fan limits
ComplianceIBR-aligned pressure-part practice
WorksShendra MIDC, Aurangabad — ISO 9001 fabrication

Available materials

Material selection follows steam pressure/temperature, condensate corrosivity and plant preference. Typical options include:

  • Tubes: Carbon steel (e.g. SA-210) for standard steam service; stainless SS304 / SS316 / SS316L where condensate or process atmosphere demands higher corrosion resistance; copper or cupro-nickel for selected low-temperature or specialty duties.
  • Fins: Aluminium for high conductivity and weight economy; copper for demanding heat transfer; stainless fins where mechanical or corrosion duty requires it.
  • Headers & connections: SA-106 Grade B or equivalent carbon steel as default; stainless headers on request for corrosive condensate return paths.
  • Casings / frames: Carbon steel with protective coating, or stainless where specified for outdoor or aggressive plant atmospheres.

Final metallurgy is confirmed against your P&ID, steam quality and inspection agency requirements.

Testing and documentation

Grandeh supports project QA with fabrication and inspection documentation aligned to industrial EPC practice:

  • Dimensional inspection and coil hydrostatic / pneumatic testing as specified
  • Material test certificates (MTC) for pressure parts
  • Welding procedure / welder qualification records where applicable
  • GA drawings, coil data sheets and as-built documents for site erection
  • Third-party inspection (TPI) coordination — e.g. Bureau Veritas, TÜV, LRQA — when called in the purchase order
  • Quality documents available to project partners via Grandeh project portal

Typical applications

  • Spent-wash / slop-fired boiler combustion-air heating
  • Biomass and high-moisture fuel boilers
  • Cold-climate and start-up air heating for package and field-erected boilers
  • Corrosion protection of downstream tubular / regenerative APHs

Industries we serve with SCAPH

  • Distillery — spent-wash / slop-fired boiler air heating
  • Sugar and process cogeneration boilers
  • Power and captive power cold-start air heating
  • Boiler OEMs — package and field-erected supply

See a recent dispatch: SCAPH coils for distillery / process duty.

FAQ

When should a plant use SCAPH instead of only a tubular APH?

When flue gas is sticky, acidic or ash-laden — common in spent-wash and some biomass boilers — or when start-up / low-load air heating is needed before the main APH is effective.

What data is required to size a SCAPH?

Air flow and temperatures, allowable air-side pressure drop, steam pressure and quality, condensate return conditions, duct size / layout, and material or inspection preferences.

How does SCAPH help with cold-end corrosion?

By lifting combustion-air temperature before the main air preheater, SCAPH helps keep cold-end metal surfaces warmer and reduces acid condensation risk on tubular or regenerative APH surfaces.

What materials does Grandeh use for SCAPH?

Carbon-steel or stainless tubes, aluminium / copper / stainless fins, and SA-106 (or stainless) headers are typical. We confirm the bill of materials against your steam and site conditions.

Can SCAPH be supplied with a new boiler or as a retrofit?

Both. Share steam pressure, air flow, required temperature lift and duct layout for sizing.

Do you support TPI and IBR documentation?

Yes. Pressure-part practice is IBR-aligned at our Aurangabad works, and we coordinate hold points with client or third-party inspectors as specified.